MANUAL FOR SUPER 7 LATHE (POWER CROSS FEED) No. S.273 W

Ref: 3522
This is a manual for the operation, installation and maintenance of a myford Super 7 lathe with a power cross feed. Comes with all the ... Read More

KA2. GIB STRIP FOR SADDLE

Ref: 2367
This Is The Gib Strip For The Saddle Of The Superr 7 Lathes With Powercross Feed. Read More

KA3. INCOMPLETE ADJUSTING SCREW GIB STRIP

Ref: 1430
Incomplete Adjusting Screw For Powerfeed Unit.. 1/4" BSF x 75MM Please Note That These Screws Haven't Been Finished Read More

KA3. INCOMPLETE ADJUSTING SCREW GIB STRIP

Ref: 1430586
Incomplete Adjusting Screw For Powerfeed Unit.. 1/4" BSF x 50MM Please Note That These Screws Haven't Been Finished Read More

KA4. ADJUSTING SCREW GIB STRIP A9184

Ref: 1920
Adjusting screw for gib strip Read More

KA6 & KA10. FULL SET OF SADDLE SHIMS 70/1304 & 70/1305

Ref: 2337
3 x Rear Laminated Shim (70/1304) 2 x Front Laminated Shim (70/1305) Read More

KA8. 1/4" BSF x 1 1/4" SOCKET CAPHEAD SCREWS - PACK OF 5 - SC8

Ref: 15309
Pack of 5 socket caphead screws Thread: 1/4" BSF x 26TPI Length: 1 1/4" Read More

KA9. 1/4" BSF x 7/8" SOCKET CAPHEAD SCREWS - PACK OF 5 - SC13

Ref: 15308
Pack of 5 socket caphead screws Thread: 1/4" BSF x 26TPI Length: 7/8" Read More

KA11. SADDLE STRIP - REAR A2122

Ref: 2338
Saddle Strip For The Rear Of The Saddle. Length 7 - 7/16" Thickness 1/4" Width - 1" Read More

KA13. SADDLE CLAMP ECCENTRIC 70/1312

Ref: 3300
This Eccentric Is Used In Conjunction With The Hard Hex Bolt That Goes Through The Saddle. When The Bolt Is Tightened, It Pushes The ... Read More

KA15. HEXAGON HEAD BOLT (HARD)

Ref: 15311
5/16" BSF x 1.1/2" This Bolt Is Used To Go Through The Saddle In To The Saddle Clamp Eccentric 70/1312 Read More

KA16. FELT WIPER FOR SERIES 7 LATHES WITH WIDE GUIDE BEDS A8735

Ref: 2339
This is the felt wiper for all power cross feed Super 7 lathes. It is used to keep swarf out from underneath the saddle. Read More

KA17. WIPER HOUSING (WIDE GUIDE BEDS) A8736

Ref: 2341
Wiper Housing For The Felt Wiper Wide Guide A8735 Goes Over The Top Of The Felt Wiper, Also comes with 4 screws for fitting your ... Read More

KA19. PACK OF 10 2BA OIL NIPPLES 33/072

Ref: 15314
Pack Of 10 Oil Nipples Threaded 2BA. Found All Over The Myford Lathes. Oil Gun To Be Used With These Is Part Number Read More

KA20. FEED GEAR FOR POWER CROSS FEED A9186

Ref: 249
This gear slots on to the feedscrew and transmits drive to the feedscrew from the power feed unit. When assembling this part, it is essential that ... Read More

KA23. LONG CROSS SLIDE A2060/2

Ref: 2342
Cross slide for Super 7 lathes. Comes complete with gib strips and adjusting screws !!<>!!!!<>!!PLEASE NOTE:!!<>!!!!<>!! This cross slide comes without the holes for ... Read More

KA24. THRUST PAD (RH) A2067

Ref: 2343
Thrust Pad Used To Hold The Top Slide Base In Place, In The Cross Slide Read More

KA25. THRUST PAD (LH) A2067A

Ref: 2344
Thrust Pad Used To Hold The Top Slide Base In Place, In The Cross Slide Read More

KA26. PAIR 3/8" BSF x 1/2" DOG POINT SCREWS FOR CROSS SLIDE (FOR NEWER LATHES)

Ref: 3304
Dog Point Screws Length 1/2" Threaded 3/8" Super 7 Lathes With Power Cross Feed. Read More

KA26. PAIR 3/8" BSF SQUARE HEADED SCREWS FOR CROSS SLIDE (FOR OLDER LATHES)

Ref: 3305
Square Headed Screws To Hold The Thrust Pads In Place Part Codes RH Thrust Pad - A2067 Part Codes LH Thrust Pad - A2067A Read More

KA29. CHEESE HEAD SCREW A2149

Ref: 3308
Cheese Head Screw For The Super 7 Cross Slide, Threades Through The Back Of The Cross Slide Into The Cross Slide Gib Strip. Read More

KA30. M5 x 16mm DOG POINT SCREWS - PACK OF 5 - SC44

Ref: 15316
Pack of 5 dog point screws Thread: M5 x 0.8mm Length: 16mm Read More

KA31. M5 x 20mm DOG POINT SCREWS - PACK OF 5 - SC45

Ref: 15317
Pack of 5 dog point screws Thread: M5 x 0.8mm Length: 20mm Read More

KA34. 2BA x 5/8" SOCKET CAPHEAD SCREWS - PACK OF 5 - SC4

Ref: 15318
Pack of 5 socket caphead screws Thread: 2BA Length: 5/8" Read More

KA36. CROSS SLIDE ADJUSTING COLLAR A9191

Ref: 2737
This is the adjusting collar for Super 7 lathes with power cross feed. Please note, the top slide adjusting collar is different (part code: A2229). Read More

KA37. COPPER PAD 11253

Ref: 4665
Copper Pad For Adjusting Collar Powercross Feed Version.. Read More

KA38. 1/4" BSF x 3/16" DOG POINT SCREWS - PACK OF 5 - SC39

Ref: 15319
Pack of 5 dog point screws Thread: 1/4" BSF x 26TPI Length: 3/16" Read More

KA39. CROSS SLIDE MICROMETER DIAL - IMPERIAL A2072/1

Ref: 395
Cross slide micrometer dial for imperial Super 7 lathes. Graduated from 0 - 100, so each graduation equates to 0.001" of movement. Read More

KA39. CROSS SLIDE MICROMETER DIAL - METRIC A3250/1

Ref: 396
Cross slide micrometer dial for metric Super 7 lathes. Graduated from 0 - 2, to suit the 2mm pitch feedscrew Read More

KA40. DIAPHRAGM WASHER A2058

Ref: 15320
Wavey Washer used To Create Friction Between Micrometer Dial And Feedscrew. Read More

KA41. BALL HANDLE ASSEMBLY - CROSS SLIDE A2073

Ref: 2347
Super 7 Chrome Cross Slide Ball Handle And All Series 7 Lathes. Read More

KA42. CHROME BALL HANDLE SECURING SCREW A1541/1

Ref: 2348
Chrome Securing Screw Used On Myford Lathes To Fix The Ball Handles In Place On The Cross Slide And Topslide. Read More

KA43. 1/4" BSF x 1/4" GRUB SCREWS - PACK OF 5 - SC57

Ref: 15321
Pack of 5 grub screws Threaded: 1/4"BSF x 26TPI Length: 1/4" Read More

KA45. IMPERIAL TOP SLIDE FEEDNUT A1456

Ref: 2352
Top slide feednut to suit imperial Super 7 lathes (10TPI thread) Read More

KA45. METRIC TOP SLIDE FEEDNUT A2166

Ref: 2353
Top slide feednut for metric Super 7 lathes (threaded 2mm pitch) Read More

KA47. 2BA GRUB SCREWS - PACK OF 5 - SC55

Ref: 15322
Pack of 5 grub screws. Threaded 2BA Read More

KA48. TOP SLIDE GIB STRIP A2078/2

Ref: 2354
gib strip for super 7 top slide Read More

KA53. FEEDSCREW AND NUT - METRIC - TOP SLIDE 30/144

Ref: 2350
Metric feedscrew and nut for super 7 cross slides Read More

KA53. FEEDSCREW AND NUT - IMPERIAL - TOP SLIDE 30/143

Ref: 2351
Imperial feedscrew and nut for Super 7 top slides. Read More

KA54. ADJUSTING COLLAR FOR TOP SLIDE LEADSCREW A2229

Ref: 2355
This Adjusting Collar Screws On To The Very Fine Threads Of The Super 7 Topslide Feedscrews. It Is Used To Take Up The Slack In ... Read More

KA55. TOP SLIDE MICROMETER DIAL - IMPERIAL A2079

Ref: 2356
Micrometer dial for imperial top slides Graduated from 0 - 1, to suit 10TPI screws (so each full rotation equates to 0.100" of travel) Read More

KA55. TOP SLIDE MICROMETER DIAL - METRIC A3249

Ref: 2357
Micrometer dial for metric Super 7 top slides. Graduated from 0 - 40, to suit the 2mm pitch feedscrew (each graduation equates to 0.05mm of movement) Read More

KA56. BALL HANDLE ASSEMBLY - TOP SLIDE A2093

Ref: 2358
Chrome Ball Handle Assembly For Myford Super 7 Lathes. This Ball Handle Is To Be Used ON The Topslide Read More

KA57. TOOLPOST STUD 70/1406

Ref: 2364
Toolpost stud threaded 7/16" BSF - used to locate the toolpost Read More

KA57 & KA62. REPLACEMENT TOOLPOST STUD AND NUT 75/1412

Ref: 2360
Toolpost Stud And Nut. Threaded 7/16" BSF DOES NOT COME SUPPLIED WITH A PIN! Read More

KA59. SPRING A2806

Ref: 2363
Spring For The Original Clamp-Type Toolpost Please Note , If You Have A Quick Change Toolpost Or 4 Way Toolpost, You Will Not Need This ... Read More

KA60. TOOL CLAMP 74/1409/1

Ref: 2361
Tool Clamp For The Original Clamp-Type Toolposts. Please Note, If You Have A Quick Change Tool Post Or 4 Way Tool Post You Will Not ... Read More

KA63. ADJUSTING SCREW ASSEMBLY 75/1413

Ref: 2362
Adjusting screw for the standard clamp type toolpost. Please note, if you have the quick change toolpost or 4-way toolpost, then you will not need ... Read More

KA65. END PLATE FOR CROSS SLIDE (POWER FEED) A9188/1

Ref: 350
Cross Slide Endplate. This Is The Only Suitable For Power Cross Feed Models (Including The Connoisseur) Fixed To The Cross slide And Holds The Feedscrew ... Read More

KA66. FEEDSCREW AND NUT - METRIC - CROSS SLIDE (POWER FEED) 30/142

Ref: 131
This is for power cross feed Super 7 lathes Read More

KA66. FEEDSCREW AND NUT - IMPERIAL - CROSS SLIDE (POWER FEED) 30/141

Ref: 130
This is for power cross feed Super 7 lathes Read More

SET OF ADJUSTING SCREWS FOR TOP SLIDE

Ref: 2345
4 X 2BA X 5/8" DOG POINT SCREW 4 X 2BA LOCKNUTS Read More

SET OF ADJUSTING SCREWS FOR SUPER 7 CROSS SLIDE

Ref: 2346
Includes: 2 x M5 x 20mm 4 x M5 x 16mm Read More