131. OILITE BUSH A2295

Ref: 69007
Oilite bush that is pressed into the gearbox casting at the right hand side. Read More

133. DRAIN PLUG (1/4" BSP)

Ref: 69009
Read More

134. OIL LEVEL PLUG A2531

Ref: 69010
Oil level plug for the right hand side of the gearbox. Read More

135. PLUG A2698

Ref: 69011
this item is used in the front of the gearbox. Read More

136. CAPTIVE SCREW A2699

Ref: 69012
This captive screw goes through the back of the gearbox. Read More

139. 1/4" BSF x 3/4" SOCKET CAPHEAD SCREWS - PACK OF 5 - SC11

Ref: 69015
Pack of 5 socket caphead screws Thread: 1/4" BSF x 26TPI Length: 3/4" Read More

141. 16T GEAR A2284

Ref: 69017
16T gear for A3005 shaft. Comes supplied undrilled, without pin. Read More

140. SHAFT A3005

Ref: 69016
Please Note That These Shafts Come As Pictured And Will Have To Be Drilled Yourself To Take The Pin.. Read More

143. 18T GEAR A2304/18

Ref: 69019
Hardened 18T gear for the A3005 shaft Read More

144. 19T GEAR A2304/19

Ref: 69020
Hardened 19T gear for the A3005 shaft Read More

145. 20T GEAR A2304/20

Ref: 69021
Hardened 20T gear for the A3005 shaft Read More

146. 22T GEAR A2304/22

Ref: 69022
Hardened 22T gear for the A3005 shaft Read More

147. 24T GEAR A2301

Ref: 69023
Hardened 24T gear for the A3005 shaft Read More

148. 26T GEAR A2304/26

Ref: 69024
Hardened 26T gear for the A3005 shaft Read More

149. 28T GEAR A2304/28

Ref: 69025
Hardened 28T gear for the A3005 shaft Read More

150. 32T GEAR A2304/32

Ref: 69026
Hardened 32T gear for the A3005 shaft Read More

151. KEY STEEL A3006

Ref: 69027
Key Steel For A3005 Shaft Goes Inside The Gearbox And Keeps All The Gears On The Shaft.. Read More

152. BUSH A3003

Ref: 69028
Steel bush to go around the clamping sleeve (A3007) Read More

153. CLAMPING SLEEVE A3007

Ref: 69029
Clamping sleeve to be pressed on to the A3005 shaft Read More

155. CLAMP WASHER A2492

Ref: 69031
Clamp Washer Used On The ML7 / Super 7 Lathes Read More

158. 2BA x 5/16" CUP POINT SCREWS - PACK OF 5 - SC26

Ref: 69033
Pack of 5 cup point screws Thread: 2BA Length: 5/16" Read More

159. LAYSHAFT A3008

Ref: 69034
Layshaft For Myford Gearbox... works with thr key a2300 Read More

160. KEY A2300

Ref: 69035
Small Piece Of Key Steel That Goes In The Gearbox, Works In Conjunction With The Layshaft (A3008) Read More

161. 32T GEAR A2308

Ref: 69036
Hardened 32T Gear For Myford Gearbox, Works In Conjunction With A2605/1 Read More

162. OILITE BUSH A2605/1

Ref: 69037
Part No... (A2605/1) Oilite Bush For 32T Gearbox Gear. Read More

163. 24T SLIDING GEAR A2306

Ref: 69038
This Is A 24T Sliding Gear, Hardened For Super 7 Gearbox Read More

164. 16T GEAR A2307

Ref: 69039
16T Gear For Myford Gearbox, Hardened Finish.. Works With Bush (A2307) Read More

165. BUSH A2494

Ref: 69040
Bush That Goes Inside The 16T Gear (A2494) Read More

166. WOODRUFF KEY No. 404 (1/8" x 1/2")

Ref: 69041
Read More

167. 26T GEAR FOR QUICK CHANGE GEARBOX A3013

Ref: 69042
26T Hardened Gear For Myford Gearbox Read More

168. 52T GEAR FOR QUICK CHANGE GEARBOX A3014

Ref: 69043
52T Gear For Myford Gearbox Lathes.. Please Note These Gears Have A Little Slight Surface Rust.. Read More

169. SELECTOR CASTING A2269

Ref: 69044
Gearbox Selector Casting, Item Comes Unpainted, No Grub Screws Suitable For Myford Series 7 Lathes With Gearbox. Read More

170. 39T TUMBLER GEAR A2299

Ref: 69045
39T Tumbler Gear, Which Engages With The 171. Spindle (A2296) Read More

171. SPINDLE A2296

Ref: 69046
Spindle To Go Through The 39T Tumblre Gear (A2299) And Is Held In Place With 172. Taper Pin No 0 x 1-1/8" Read More

174. 2BA x 1/4" CUP POINT SCREWS - PACK OF 5 - SC24

Ref: 69048
Pack of 5 cup point screws Thread: 2BA Length: 1/4" Read More

180. PEG END GRUB SCREW A2542

Ref: 69051
Read More

181. COPPER PAD

Ref: 69052
Copper Pad Diameter 3/16" Read More

182. 1/4" BSF x 3/4" DOG POINT SCREWS - PACK OF 5 - SC40

Ref: 69053
Pack of 5 dog point screws Thread: 1/4" BSF x 26TPI Length: 3/4" Read More

INPUT SHAFT IN HOUSING A3010/1

Ref: 69055
Consists of 183. A3010 Input Shaft and 179. A3009 Housing. Read More

184. COLLAR MA2241

Ref: 69056
This is only for Super 7 / ML7 lathes WITHOUT a quick change gearbox Inside Bore - 5/8" Does Not Come With Grub ... Read More

186. 72T GEAR A2327

Ref: 69058
Large 72T Gear For The Gear Train On The Outside Of The Gearbox Goes At The End Of The 186. Input Shaft (A3010) Read More

188. 7/16" BSF FULL NUTS - PACK OF 5 - SC53

Ref: 69060
Pack of 5 full nuts. Threaded 7/16" BSF x 18TPI Read More

189. PACK OF 10 2BA OIL NIPPLES 33/072

Ref: 69061
Pack of 10 oil nipples threaded 2BA. Found all over the Myford lathes. Oil Gun to be used with these is part number 15472 Read More

193. QUADRANT PLATE A2272

Ref: 69062
Quadrant Plate Used In Conjunction With The Upper Lever A2511 And Pivot Pin A2293 To Move The Sliding Gear And Adjust The Feed Rate.. Read More

194. PIVOT PIN A2293

Ref: 69063
This Pin Is Fixed To The Quadrant Plate From Under The Gearbox Lid Read More

195. 1/4" BSF x 5/16" CUP POINT SCREWS - PACK OF 5 - SC30

Ref: 69064
Pack of 5 cup point screws Thread: 1/4" BSF x 26TPI Length: 5/16" Read More

196. THRUST BLOCK A2286

Ref: 69065
This thrust block fits to the quadrant plate Read More

197. UPPER LEVER FOR GEARBOX A2511

Ref: 69066
Lever That Sits On The Top Of The Gearbox, Used To Select The Feed Rate.. This Lever Is Just Push Fit With A 1/4" Grub Screw ... Read More

201. GEARBOX SCREW CUTTING CHART A2602/2

Ref: 69068
Screwcutting chart for the top of the gearbox Read More

203. ANCHOR PIN A3015

Ref: 69070
Anchor Pin Used In The Gearbox, This Sits In The Left Hand Side Of The Gearbox. Threaded 3/8" Read More

205. 3/8" BSF FULL NUTS - PACK OF 5 - SC51

Ref: 69072
Pack of 5 full nuts. Threaded 3/8" BSF x 20TPI Read More

206. GEAR STUD A2330/2

Ref: 69073
Gear Stud For Myford Gearbox Works In Conjunction With 19/57T Reversible Gear A2330/2 Read More

207. 5/16" BSF LOCK NUTS / HALF NUTS - PACK OF 5 - SC69

Ref: 69074
Pack of 5 locknuts (or halfnuts) Threaded 5/16" BSF x 22TPI Read More

208. REVERSIBLE CLUSTER GEAR 19/57T A2326/1

Ref: 69075
Reversible Cluster Gear From The Gear Train, Used When Cutting Fine Feeds Small Gear 19T Large Gear 57T Read More

209. GEAR STUD A2329/2

Ref: 69076
Gear Stud For Myford Gearbox Works In Conjunction With 19/57T Fixed Cluster Gear A2325/1 Read More

210. FIXED CLUSTER GEAR 19/57T A2325/1

Ref: 69077
Fixed Cluster Gear For The Gear Train.. Small Gear 19T Large Gear 57T Read More

211. LINK A2331

Ref: 69078
Link That Goes Between Both Studs On The Gear Train.. Read More

212. WASHER VT220

Ref: 69079
Washer Goes Between Reataining Screw (A1999) And The Link A2331 Read More

213. TUMBLER SLEEVE GEAR RETAINING SCREW A1999

Ref: 69080
Retaining Screw Screws Into The End Of The Gear Stud ( A2329/2 ) Screw Also Has A Hollow Channel To Provide Lubrication Read More

214. 24T GEAR A3115

Ref: 69081
This Is Just A Standard 24T Changewheel Part Code - 11285/24 Changewheel For Any Series 7, Series 10 or 254 Lathes. 20DP, 14.5° Pressure ... Read More

216. RUBBER PAD A2023

Ref: 69082
Rubber Pad Used To Cushion Guards When Closing Them. Read More

217. 1/4" BSF x 1" HEXAGON HEAD BOLT - SC63

Ref: 69083
Hexagon Head Bolt Thread: 1/4" BSF x 26TPI Length: 1" Read More

219. 2BA x 1" SOCKET CAPHEAD SCREWS - PACK OF 5 - SC2

Ref: 69084
Pack of 5 socket caphead screws Thread: 2BA Length: 1" Read More

220. STUD A3017

Ref: 69085
Stud which Goes Through The Backplate (A2963) And Into The Lathe Bed With A 1/4" BSF Nut Holding The Backplate (A2963) In Place . ... Read More

221. 1/4" OIL BLACKENED WASHERS - PACK OF 10 - SC88

Ref: 69086
Pack of 10 Oil Blackened Washers. Inside Bore - 1/4" Outside Diameter - 9/16" Read More

222. 1/4" BSF LOCK NUTS / HALF NUTS - PACK OF 5 - SC67

Ref: 69087
Pack of 5 locknuts (or halfnuts) Threaded 1/4" BSF x 26TPI Read More

223. HINGE SCREW FOR GUARD A2024

Ref: 69088
5/16" BSF X 1" Cone Point Screw Which Holds The Backplate A2963 And A2528/1 Changewheel Guard Together. Read More

224. TENSION SPRING A2012

Ref: 69089
Tension Spring Used In Conjunction With The Spring Clip A3018 To Keep The Gear Train Guard Closed Read More

225. 2BA x 5/16" ROUND HEAD SCREWS - PACK OF 5 - SC75

Ref: 69090
Pack of 5 round head screws Thread: 2BA Length: 5/16" Read More

226. CHANGEWHEEL GUARD (ML7) A2527/1

Ref: 69091
Myford ML7 Rough Changewheel Guard Casting, This Guard Will Come Unpainted, But Comes Drilled. Read More

228. GEARBOX PLATE - METRIC PITCHES A7934

Ref: 69093
Plate that fits inside gearbox Read More

229. SPRING CLIP A3018

Ref: 69094
Spring Clip For Super 7 Guards, Will Help Keep Your Guards Closed, Read More

NEW VERSION OF PART 229

Ref: 69095
This Is The Spring Clip For New Models Of The Super 7, This Part Replaces Part 229 On The Exploaded Parts Diagram Read More

231. 1/4" BSF x 3/4" SOCKET CAPHEAD SCREWS - PACK OF 5 - SC11

Ref: 69096
Pack of 5 socket caphead screws Thread: 1/4" BSF x 26TPI Length: 3/4" Read More

234. CHANGE GEAR QUADRANT FOR METRIC CONVERSION KIT A2469

Ref: 69099
Change Gear Quadrant For Metric Conversion Kits, Comes In Green Grey Or Aqua.. Length Of Longest Slot - 117MM Length Of Short Slot - 56MM ... Read More

235. CHANGEWHEEL STUD A1496/2

Ref: 69100
For The Metric Conversion Kits.. This Is The Stud That The Sleev A1501 And Bush A1500 Slide On To, To Accept The Changewheels.. For The ... Read More

236. SLEEVE A1501

Ref: 69101
For the metric conversion kits. Read More

238. WASHER A1498

Ref: 69103
This Is The Washer used On The Changewheel Stud Inside Diamter - 6.25mm Read More

239. 1/4" BSF FULL NUTS - PACK OF 5 - SC50

Ref: 69104
Pack of 5 full nuts. Threaded 1/4" BSF x 26TPI Read More

241. SPACER A2604

Ref: 69106
For the metric conversion kits. Spacer to be used on the gear train Read More

242. 60T CHANGEWHEEL 11285/60

Ref: 69107
For the metric conversion kits. Standard changewheel, needed to cut the metric threads. 20DP, 14.5° pressure angle, 5/8" bore, 3/8" thick. Read More

243. 63T CHANGEWHEEL 11285/63

Ref: 69108
For the metric conversion kits. Standard changewheel, needed to cut the metric threads. 20DP, 14.5° pressure angle, 5/8" bore, 3/8" thick. Read More

244. 50T CHANGEWHEEL 11285/50

Ref: 69109
For the metric conversion kits. Standard changewheel, needed to cut the metric threads. 20DP, 14.5° pressure angle, 5/8" bore, 3/8" thick. Read More

245. 45T CHANGEWHEEL 11285/45

Ref: 69110
For the metric conversion kits. Standard changewheel, needed to cut the metric threads. 20DP, 14.5° pressure angle, 5/8" bore, 3/8" thick. Read More

246. 28T CHANGEWHEEL 11285/28

Ref: 69111
For the metric conversion kits. Standard changewheel, needed to cut the metric threads. 20DP, 14.5° pressure angle, 5/8" bore, 3/8" thick. Read More

248. 35T CHANGEWHEEL 11285/35

Ref: 69113
For the metric conversion kits. Standard changewheel, needed to cut the metric threads. 20DP, 14.5° pressure angle, 5/8" bore, 3/8" thick. Read More

249. 40T CHANGEWHEEL 11285/40

Ref: 69114
For the metric conversion kits. Standard changewheel, needed to cut the metric threads. 20DP, 14.5° pressure angle, 5/8" bore, 3/8" thick. Read More

250. 55T CHANGEWHEEL 11285/55

Ref: 69115
For the metric conversion kits. Standard changewheel, needed to cut the metric threads. 20DP, 14.5° pressure angle, 5/8" bore, 3/8" thick. Read More

252. 1/4" BSF x 1/2" SOCKET CAPHEAD SCREWS - PACK OF 5 - SC10

Ref: 69117
Pack of 5 socket caphead screws Thread: 1/4" BSF x 26TPI Length: 1/2" Read More

256. 7/16" BSF LOCK NUTS / HALF NUTS - PACK OF 5 - SC70

Ref: 69120
Pack of 5 locknuts (or halfnuts) Threaded 7/16" BSF x 18TPI Read More

258. THRUST COLLAR 75/1115/1

Ref: 69121
For The Right Hand Side Of The Leadscrew Comes With Grub Screw Inside Bore - 7/16" Read More

259. PAIR OF OIL NIPPLES FOR TOP OF GEARBOX

Ref: 69122
Oil Nipples That Go In The Top Of The Gearbox Lid These Are Push Fit 1/4" Read More

261. RIVET (No. 0 x 3/16")

Ref: 69124
No.0 X 3/16" Round Head Hammer Drive Rivets Comes In Pack Of 4 Read More

262. PLUNGER HOUSING A2297/1

Ref: 69125
Plunger Houseing For Myford Gearbox.. Suitable For All Series 7 Lathes With A Gearbox. Read More

263. PLUNGER A2279/1

Ref: 69126
Plunger For The Gearbox Selector Lever (A2269) On The Front Of The Gearbox. Also Works In Conjunction With The Plunger Housing (A2279/1) Going Straight Throught The ... Read More

264. KNOB A2519

Ref: 69127
For The Plunger A2279/1 And For The Selecter Lever A2296 Read More

175, 262 - 265. KNOB/PLUNGER ASSEMBLY

Ref: 69129
Includes A2612, A2297/1, A2279/1, A2591/1 & Anderton Circlip Read More

REAR PACKING STRIP FOR GEARBOX (SUPER 7) A2652

Ref: 69130
To Go Between The Gearbox And The Lathe When Installing. PLEASE NOTE - It Is Important That This Is In Place On The Super 7 ... Read More