MANUAL FOR ML7-R LATHE No. 752A

Ref: 3533
This is a manual for the operation, installation and maintenance of a Myford ML7-R lathe. Also has a very good pictorial parts list with exploded ... Read More

131. OILITE BUSH A2295

Ref: 1957
Oilite bush that is pressed into the gearbox casting at the right hand side. Read More

132. SEALING WASHER (DOWTY SELON MARK 5)

Ref: 15894
Sealing Washer For Myford Gearbox Lathes Will Come As A Pair Fits ML7 ML7-R And Super 7 Lathes Read More

133. DRAIN PLUG (1/4" BSP)

Ref: 1175
Box 38H Read More

134. OIL LEVEL PLUG A2531

Ref: 2129
Oil level plug for the right hand side of the gearbox. Read More

135. PLUG A2698

Ref: 1314
this item is used in the front of the gearbox. Read More

136. CAPTIVE SCREW A2699

Ref: 1910
This captive screw goes through the back of the gearbox. Read More

137. SPRING WASHER (1/4" TERRYS 159)

Ref: 15895
Spring Washer Used On The Myford Quick Change Gearbox Diameter - 1/4" Come As A Pair. Read More

140. SHAFT A3005

Ref: 1265
Please Note That These Shafts Will Have To Be Drilled Yourself To Take The Pin.. Read More

141. 16T GEAR A2284

Ref: 1176
16T gear for A3005 shaft. Comes supplied undrilled, without pin. Read More

143. 18T GEAR A2304/18

Ref: 1177
Hardened 18T gear for the A3005 shaft Read More

144. 19T GEAR A2304/19

Ref: 1178
Hardened 19T gear for the A3005 shaft Read More

145. 20T GEAR A2304/20

Ref: 1179
Hardened 20T gear for the A3005 shaft Read More

146. 22T GEAR A2304/22

Ref: 1180
Hardened 22T gear for the A3005 shaft Read More

147. 24T GEAR A2301

Ref: 1181
Hardened 24T gear for the A3005 shaft Read More

148. 26T GEAR A2304/26

Ref: 1182
Hardened 26T gear for the A3005 shaft Read More

149. 28T GEAR A2304/28

Ref: 1183
Hardened 28T gear for the A3005 shaft Read More

150. 32T GEAR A2304/32

Ref: 1184
Hardened 32T gear for the A3005 shaft Read More

151. KEY STEEL A3006

Ref: 15907
Key Steel For A3005 Shaft Goes Inside The Gearbox And Keeps All The Gears On The Shaft.. Read More

153. CLAMPING SLEEVE A3007

Ref: 1372
Clamping Sleeve To Be Pressed On To The A3005 Shaft Read More

155. CLAMP WASHER A2492

Ref: 15901
Clamp Washer Used On The ML7 / Super 7 Lathes Read More

156. 1/4" BSF x 1" COUNTERSUNK SCREW - PACK OF 5 - SC23

Ref: 15902
Pack of 5 countersunk screws Thread: 1/4" BSF x 26TPI Length: 1" Read More

158. 2BA x 5/16" CUP POINT SCREWS - PACK OF 5 - SC26

Ref: 15903
Pack of 5 cup point screws Thread: 2BA Length: 5/16" Read More

159. LAYSHAFT A3008

Ref: 15904
Layshaft For Myford Gearbox... Read More

161. 32T GEAR A2308

Ref: 15906
Hardened 32T Gear For Myford Gearbox, Works In Conjunction With A2605/1 Read More

162. OILITE BUSH A2605/1

Ref: 1710
Part No... (A2605/1) Oilite Bush For 32T Gearbox Gear. Read More

163. 24T SLIDING GEAR A2306

Ref: 1766
This Is A 24T Sliding Gear, Hardened For Super 7 Gearbox Read More

164. 16T GEAR A2307

Ref: 15910
16T Gear For Myford Gearbox, Hardened Finish.. Works With Bush (A2307) Read More

165. BUSH A2494

Ref: 15911
Bush That Goes Inside The 16T Gear (A2494) Read More

166. WOODRUFF KEY No. 404 (1/8" x 1/2")

Ref: 15912
1/8" x 1/2" Read More

167. 26T GEAR FOR QUICK CHANGE GEARBOX A3013

Ref: 1185
26T gear for gearbox Read More

168. 52T GEAR FOR QUICK CHANGE GEARBOX A3014

Ref: 1186
52T gear for gearbox Read More

169. SELECTOR CASTING A2269

Ref: 15913
Gearbox Selector Casting, Item Comes Unpainted, No Grub Screws Suitable For Myford Series 7 Lathes With Gearbox. Read More

170 & 171. 39T TUMBLER GEAR & SPINDLE A2299 / A2296

Ref: 15914
39T Tumbler Gear, Which Engages With The 171. Spindle (A2296) Comes As A Matched Pair With Spindle Read More

175. SPRING A2612

Ref: 15918
Small Spring For The Plunger (A2279/1) And Selecter (A2269/1) Read More

175. 262 - 265. KNOB/PLUNGER ASSEMBLY

Ref: 8591885
Includes A2612, A2297/1, A2279/1, A2591/1 & Anderton Circlip Read More

180. PEG END GRUB SCREW A2542

Ref: 15920
Peg End Grub Screw For Myford Gearbox. Read More

181. COPPER PAD 11253

Ref: 15921
Copper Pad Diameter 3/16" Read More

182. 1/4" BSF x 3/4" DOG POINT SCREWS - PACK OF 5 - SC40

Ref: 15922
Pack of 5 dog point screws Thread: 1/4" BSF x 26TPI Length: 3/4" Read More

INPUT SHAFT IN HOUSING A3010/1

Ref: 1187
Consists of 183. A3010 Input Shaft and 179. A3009 Housing. Will Need To Buy Collar (MA2241) Read More

184. COLLAR MA2241/11286

Ref: 15925
This is only for Super 7 / ML7 lathes WITHOUT a quick change gearbox Inside Bore - 5/8" Does Not Come With ... Read More

186. 72T GEAR A2327

Ref: 1188
Large 72T Gear For The Gear Train On The Outside Of The Gearbox Goes At The End Of The 186. Input Shaft (A3010) Read More

187. 7/16" OIL BLACKENED WASHERS - PACK OF 10 - SC92

Ref: 15927
Pack Of 10 Oil Blackened Washers 7/16" Inside Bore. Read More

188. 7/16" BSF FULL NUTS - PACK OF 5 - SC53

Ref: 15928
Pack Of 5 Full Nuts. Threaded 7/16" BSF x 18TPI Read More

189. PACK OF 10 2BA OIL NIPPLES 33/072

Ref: 15929
Pack of 10 oil nipples threaded 2BA. Found all over the Myford lathes. Oil Gun to be used with these is part number Read More

191. LEADSCREW, STANDARD BED WITH GEARBOX - 5/8" DIAMETER - IMPERIAL

Ref: 58956412
For Standard Bed ML7 Lathes With A Gearbox, UP TO Serial Number K111727 Leadscrew Has 5/8" Diameter And Is Threaded 8TPI. NON POWERFEED LEADSCREW Read More

193. QUADRANT PLATE A2272

Ref: 1696
Quadrant plate used in conjunction with the upper lever and pivot pin to move the sliding gear and adjust the feed rate. Read More

194. PIVOT PIN A2293

Ref: 2701
This Pin Is Fixed To The Quadrant Plate From Under The Gearbox Lid Length 42.85MM Read More

196. THRUST BLOCK A2286

Ref: 1189
This Thrust Block Fits To The Quadrant Plate Read More

197. UPPER LEVER FOR GEARBOX A2511

Ref: 1190
Lever That Sits On The Top Of The Gearbox, Used To Select The Feed Rate.. This Lever Is Just Push Fit With A 1/4" Grub ... Read More

201. GEARBOX SCREW CUTTING CHART A2602/2

Ref: 1191
Screwcutting chart for the top of the gearbox Read More

203. ANCHOR PIN A3015

Ref: 15960
Anchor Pin Used In The Gearbox, This Sits In The Left Hand Side Of The Gearbox. Threaded 3/8" Read More

204. 3/8" OIL BLACKENED WASHERS - PACK OF 10 - SC90

Ref: 15961
Pack of 10 oil blackened washers, with a 3/8" inside bore. Read More

205. 3/8" BSF FULL NUTS - PACK OF 5 - SC51

Ref: 15962
Pack of 5 full nuts. Threaded 3/8" BSF x 20TPI Read More

207. 5/16" BSF LOCK NUTS / HALF NUTS - PACK OF 5 - SC69

Ref: 41515578
Pack of 5 locknuts (or halfnuts) Threaded 5/16" BSF x 22TPI Read More

208. REVERSIBLE CLUSTER GEAR 19/57T A2326/1

Ref: 1194
Reversible Cluster Gear From The Gear Train, Used When Cutting Fine Feeds Small Gear 19T Large Gear 57T Inside Bore 15.80MM Read More

210. FIXED CLUSTER GEAR 19/57T A2325/1

Ref: 1195
Fixed Cluster Gear For The Gear Train.. Small Gear 19T Large Gear 57T Bore 15.80MM Read More

212. WASHER VT220

Ref: 15963
Washer Goes Between Reataining Screw (A1999) And The Link A2331 Inside Bore - 5MM Read More

213. TUMBLER SLEEVE GEAR RETAINING SCREW A1999

Ref: 15964
Retaining Screw Screws Into The End Of The Gear Stud ( A2329/2 ) Screw Also Has A Hollow Channel To Provide Lubrication Read More

214. 24T GEAR A3115

Ref: 15965
This Is Just A Standard 24T Changewheel Part Code - 11285/24 Changewheel For Any Series 7, Series 10 or 254 Lathes. 20DP, 14.5° Pressure ... Read More

219. 2BA x 1" SOCKET CAPHEAD SCREWS - PACK OF 5 - SC2

Ref: 15968
Pack of 5 socket caphead screws Thread: 2BA Length: 1" Read More

220. STUD A3017

Ref: 15969
Stud which Goes Through The Backplate (A2963) And Into The Lathe Bed With A 1/4" BSF Nut Holding The Backplate (A2963) In Place . ... Read More

221. 1/4" OIL BLACKENED WASHERS - PACK OF 10 - SC88

Ref: 15970
Pack of 10 Oil Blackened Washers. Inside Bore - 1/4" Read More

223. HINGE SCREW FOR GUARD A2024

Ref: 1924
5/16" BSF x 1" cone point screw Read More

224. TENSION SPRING A2012

Ref: 157588
Tension Spring Used In Conjunction With The Spring Clip A3018 To Keep The Gear Train Guard Closed Read More

225. 2BA x 5/16" ROUND HEAD SCREWS - PACK OF 5 - SC75

Ref: 158589
Pack of 5 round head screws Thread: 2BA Length: 5/16" Read More

226. CHANGEWHEEL GUARD (ML7) A2527/1

Ref: 1555690
Gearbox Guard For ML7 Lathes.. This Guard Comes As a Blank Casting, It Is Needs Drilling And Just Priming And Painting. Read More

227. CHANGEWHEEL GUARD (SUPER 7) & (ML7-R) A2528/1

Ref: 1559189
Myford Super7 Rough Changewheel Guard Casting, This Guard Will Come Unpainted And Undrilled Read More

228. GEARBOX PLATE - METRIC PITCHES A7934

Ref: 1197
Plate that fits inside gearbox Read More

229. SPRING CLIP A3018

Ref: 15972
Spring Clip For Super 7 Guards, Will Help Keep Your Guards Closed, Read More

229. SPRING CLIP (NEW STYLE) A3018

Ref: 15973
This is the spring clip for the newer models of Super 7, and replaces part 229 on the diagram below Read More

252. 1/4" BSF x 1/2" SOCKET CAPHEAD SCREWS - PACK OF 5 - SC10

Ref: 15950
Pack of 5 socket caphead screws Thread: 1/4" BSF x 26TPI Length: 1/2" Read More

254. BACKPLATE A2963

Ref: 15951
Myford Super7 Rough Backplate Guard Casting, This Guard Will Come Unpainted And Undrilled. Fits To The Back Of The Super7 Changewheel Guard A2528/1 Read More

256. 7/16" BSF LOCK NUTS / HALF NUTS - PACK OF 5 - SC70

Ref: 15953
Pack of 5 locknuts (or halfnuts) Threaded 7/16" BSF x 18TPI Read More

258. THRUST COLLAR 75/1115/1

Ref: 15954
For The Right Hand Side Of The Leadscrew Comes With Grub Screw Inside Bore - 7/16" Read More

259. PAIR OF OIL NIPPLES FOR TOP OF GEARBOX

Ref: 15955
Oil Nipples That Go In The Top Of The Gearbox Lid These Are Push Fit 1/4" Read More

262. PLUNGER HOUSING A2297/1

Ref: 15958
Plunger Houseing For Myford Gearbox.. Suitable For All Series 7 Lathes With A Gearbox. Read More

264. KNOB A2519

Ref: 1881
For The Plunger A2279/1 And For The Selecter Lever A2296 Read More

267. M6 x 1mm x 20mm SOCKET CAPHEAD SCREWS - PACK OF 5 - SC15

Ref: 857
Pack of 5 socket caphead screws. Thread: M6 x 1 Length: 20mm Read More

268. GEAR STUD A2330/2

Ref: 1193
Gear Stud For Myford Gearbox Works In Conjunction With 19/57T Reversible Gear A2330/2 Read More

269. GEAR STUD A2329/2

Ref: 1261
Gear Stud For Myford Gearbox Works In Conjunction With 19/57T Fixed Cluster Gear A2325/1 Read More

270. LINK A2331

Ref: 1196
Link between both studs on the gear train. Read More

271. PLUNGER A2279/2

Ref: 1199
Plunger For The Gearbox Selector Lever (A2269) On The Front Of The Gearbox. Also Works In Conjunction With The Plunger Housing (A2279/1) Going Straight Throught ... Read More

234. GREEN CHANGE GEAR QUADRANT FOR METRIC CONVERSION KIT A2469

Ref: 15932
Change Gear Quadrant For Metric Conversion Kits Comes With Caphead Read More

234. GREY CHANGE GEAR QUADRANT FOR METRIC CONVERSION KIT A2469

Ref: 1593259

OUT OF STOCK

Change Gear Quadrant For Metric Conversion Kits Comes With Caphead Read More

234. AQUA CHANGE GEAR QUADRANT FOR METRIC CONVERSION KIT - A2469

Ref: 1593256
Change Gear Quadrant For Metric Conversion Kits Comes With Caphead Read More

235. CHANGEWHEEL STUD A1496/2

Ref: 15933
For the metric conversion kits. This is the stud that the sleeve (A1501) and bush (a1500) slide on to, to accept the changewheels. Read More

238. WASHER A1498

Ref: 15936
For the metric conversion kits. This is the washer used on the changewheel stud Read More

241. SPACER A2604

Ref: 15939
For the metric conversion kits. Spacer to be used on the gear train Read More

242. 60T CHANGEWHEEL 11285/60

Ref: 15940
For the metric conversion kits. Standard changewheel, needed to cut the metric threads. 20DP, 14.5° pressure angle, 5/8" bore, 3/8" thick. Read More

243. 63T CHANGEWHEEL 11285/63

Ref: 15941
For the metric conversion kits. Standard changewheel, needed to cut the metric threads. 20DP, 14.5° pressure angle, 5/8" bore, 3/8" thick. Read More

244. 50T CHANGEWHEEL 11285/50

Ref: 15942
For the metric conversion kits. Standard changewheel, needed to cut the metric threads. 20DP, 14.5° pressure angle, 5/8" bore, 3/8" thick. Read More

245. 45T CHANGEWHEEL 11285/45

Ref: 15943
For the metric conversion kits. Standard changewheel, needed to cut the metric threads. 20DP, 14.5° pressure angle, 5/8" bore, 3/8" thick. Read More

246. 28T CHANGEWHEEL 11285/28

Ref: 15944
For the metric conversion kits. Standard changewheel, needed to cut the metric threads. 20DP, 14.5° pressure angle, 5/8" bore, 3/8" thick. Read More

248. 35T CHANGEWHEEL 11285/35

Ref: 15946
For the metric conversion kits. Standard changewheel, needed to cut the metric threads. 20DP, 14.5° pressure angle, 5/8" bore, 3/8" thick. Read More

249. 40T CHANGEWHEEL 11285/40

Ref: 15947
For the metric conversion kits. Standard changewheel, needed to cut the metric threads. 20DP, 14.5° pressure angle, 5/8" bore, 3/8" thick. Read More

250. 55T CHANGEWHEEL 11285/55

Ref: 15948
For the metric conversion kits. Standard changewheel, needed to cut the metric threads. 20DP, 14.5° pressure angle, 5/8" bore, 3/8" thick. Read More

175, 262 - 265. KNOB/PLUNGER ASSEMBLY

Ref: 1886
Includes A2612, A2297/1, A2279/1, A2591/1 & Anderton Circlip Read More